Fast, Reliable Gate Parts & Welding Across Burlingame
Gate parts and welding in Burlingame typically runs $180–$650 depending on whether you’re dealing with a seized hinge, a root-heaved post, or full custom fabrication. Most hinge replacements and small welding jobs on the Peninsula get finished same day. Call (866) 550-7854 for a free estimate and we’ll give you a straight answer on what’s needed.
We’ve been crossing the Bay to work in Burlingame for years. Isaac Bloom and our Gate Parts & Welding team know the flatlands and the hills equally well — from the Spanish Colonials in Easton Addition to the graded driveways up in Burlingame Hills. The salt air, the fog, the old iron, the protected trees — it’s not new territory for us. Eleven years on gates exclusively means we’ve seen what this specific coastline does to hardware.
Why Highpoint Gate Repair California Is Burlingame’s Preferred Gate Parts & Welding Company
446 customer reviews averaging 4.6 stars — that’s the track record, not a promise. In Burlingame specifically, we get called back because the same person who quotes the job (Isaac) shows up to do the welding. No subcontractor handoffs, no franchise dispatchers guessing at your gate’s age.
Response time to Burlingame is typically same-day or next-morning from our Bay Area routing. We carry hinge kits, post hardware, and welding equipment on every truck, so we’re not making two trips because a 1950s wrought-iron gate needs a bracket fabricated on-site.
The local knowledge matters here more than most places. Burlingame’s tree ordinance, its salt-corrosion patterns, its obsolete opener stock — these aren’t footnotes. They’re the main event on most service calls we run in the 94010 and 94011 ZIP codes.
Our Gate Parts & Welding Services in Burlingame
Hinge Replacement
Hinge replacement in Burlingame runs $180–$320 for most residential gates. The coastal fog here keeps hinge pins perpetually damp, and the salt-laden marine air off the Bay welds them solid faster than you’d expect. We’ve cut out rust-frozen hinges on Easton Addition homes where the original pin hadn’t moved since the Truman administration. We stock heavy-duty stainless and galvanized hinge sets for salt-air environments, and we match the load rating to your gate’s actual weight — not whatever was cheapest at the hardware store.
Post Replacement
Post replacement in Burlingame typically costs $450–$850 installed, but tree-root complications can push that higher. Here’s the local reality: Burlingame’s protected liquidambar and sycamore street trees, the ones that give the City of Trees its name, heave concrete and shift post footings by 2–3 inches as their root systems expand. We’ve reset posts on Broadway and in the Easton Addition where the alignment was wrecked not by poor installation, but by decades of root growth. Because Burlingame’s tree preservation ordinance can restrict excavation within protected root zones, a post-reset job sometimes requires a city arborist consult before concrete work begins. We know the process. We’ve done it.
Rail Repair
Bent or cracked gate rails in Burlingame run $280–$520 to repair, depending on whether we’re straightening, section-replacing, or full-fabricating. The older wrought-iron gates in the flatlands often have rail profiles that haven’t been manufactured in sixty years. When we can’t source a match, we fabricate it. On-site welding means your gate doesn’t leave the property on a flatbed for three weeks.
Custom Welding
Custom welding in Burlingame starts around $350 for bracket fabrication and runs to $650+ for structural gate repairs. This is where our Gate Parts & Welding capability separates us from technicians who only swap motors. On a Spanish Colonial in Easton Addition, we replaced a seized hinge pin and a rusted-out BFT operator housing on a 1950s wrought-iron gate. The homeowner had tried generic parts, but the salt-laden marine air had accelerated corrosion beyond repair; we custom-welded a stainless steel bracket and installed a new LiftMaster operator, preserving the original gate profile. The gate looked the same. It just worked again.
Gate Rollers
Slide gate roller replacement in Burlingame costs $220–$380. The salt air chews through roller bearings fast here — we’ve replaced rollers on hillside driveways in Burlingame Hills where the grade adds extra load, and on flatland properties where root-heaved track has been grinding rollers unevenly for years.
Latch & Lock
Latch and lock repair or replacement runs $150–$290 in Burlingame. For original 1950s wrought-iron gates, we can custom-weld latches that match the existing design instead of bolting on a modern box that looks wrong. Details matter on these homes.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Burlingame
We work on nine major gate and opener brands — your system is not unfamiliar territory. In Burlingame specifically, we stock parts for LiftMaster, FAAC, and BFT systems, plus we can source for Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. The legacy openers in older Burlingame homes (those early BFT and Linear units from the 1980s and 90s) are often past direct parts availability. When that’s the case, we retrofit to a modern FAAC or LiftMaster operator that fits the existing gate geometry. We don’t upsell a full gate replacement just because the opener’s obsolete.
Common Gate Parts & Welding Problems We See in Burlingame Homes
- Rust-welded hinge pins from decades of coastal fog and salt air. Burlingame’s position on the Bay shoreline means prevailing westerlies push salt-laden marine air across driveways year-round. Untreated steel components corrode noticeably faster here than even a few miles inland in San Mateo. We’ve cut out hinges that were essentially fused solid.
- Root-heaved post footings shifting gate alignment by 2–3 inches. The mature, municipally protected street trees that define Burlingame’s identity — many planted in the 1930s–1950s — routinely heave concrete pads and shift gate post footings. Unlike neighboring Peninsula cities, technicians here must frequently address root-driven post lean while navigating strict tree preservation ordinances before any concrete work can be repoured.
- Obsolete openers with no direct replacement parts. Early BFT or Linear models from the 1980s and 90s have reached end-of-life for factory support. We retrofit these systems to modern operators while preserving the original gate structure, which is especially important for the ornamental wrought-iron gates that contribute to Burlingame’s historic streetscape.
- Salt-corroded operator housings and control boards. The near-daily coastal fog keeps hardware perpetually damp. We’ve replaced FAAC and LiftMaster operator housings on Burlingame properties where the internal electronics were fine but the enclosure had rusted through, letting moisture destroy the board.
Pricing for Gate Parts & Welding in Burlingame, CA
| Service | Typical Range in Burlingame |
|---|---|
| Hinge replacement (single) | $180–$320 |
| Post replacement (standard) | $450–$850 |
| Rail repair / straightening | $280–$520 |
| Custom welding (bracket to structural) | $350–$650+ |
| Gate roller replacement (set) | $220–$380 |
| Latch / lock repair or replacement | $150–$290 |
| Full opener retrofit (legacy to modern) | $850–$1,400 |
What moves you within these ranges? Gate material (wrought iron vs. aluminum), access difficulty (steep Burlingame Hills driveways take longer), and whether tree-root issues require arborist coordination. We quote upfront before starting work — call (866) 550-7854 for an exact number on your specific gate. Estimates are free.
We Also Serve Cities Near Burlingame
Our service radius covers the full Peninsula corridor. We regularly run calls in Hillsborough, Millbrae, San Mateo, and San Bruno — often same-day when routing allows. If you’re in one of these neighboring cities and have a legacy gate, salt-corrosion damage, or root-heaved posts, the same crew and equipment that serves Burlingame can be on your driveway quickly.
Serving Burlingame, CA — Our Local Coverage Area
We’re based in the Burlingame area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs — Gate Parts & Welding in Burlingame
We can usually match or fabricate a compatible spring, but the opener itself may need evaluation separately. Original springs on 1940s Burlingame gates are often custom-wound to specifications that haven’t been catalogued in decades. We source from specialty suppliers or wind springs in-house to match the original torque requirements. The opener is a different question — if it’s an obsolete Linear or early BFT model with no parts availability, we’ll retrofit to a modern LiftMaster or FAAC unit that fits your gate’s geometry without replacing the ironwork. Call (866) 550-7854 and we’ll inspect both components on the same visit.
Yes, we regularly realign root-heaved posts in Burlingame without trenching through protected root zones. The method depends on how far the post has shifted — sometimes custom shimming and bracket adjustment gets the gate operating true again. Other cases require a full post reset with an arborist-approved footing design that routes around critical roots. We’ve worked within Burlingame’s tree ordinance requirements on properties near Broadway and in the Easton Addition. The arborist consult adds a few days but protects both your tree and your gate long-term. Call (866) 550-7854 to schedule an assessment.
No — most Linear operators from the 1980s have reached end-of-life for factory parts support. We don’t waste your time hunting obsolete boards or motors that don’t exist. Instead, we retrofit a modern operator (typically LiftMaster or FAAC for Burlingame’s salt-air environment) to your existing gate structure. The new unit mounts to your current posts and connects to your existing wiring where possible. For ornamental wrought-iron gates, we fabricate custom brackets so the modern operator doesn’t visually intrude. Retrofit cost typically runs $850–$1,400 depending on gate weight and access-control features. Call (866) 550-7854 for a specific quote.
Every 60–90 days with a lithium-based grease rated for marine environments. Burlingame’s salt-laden fog makes the standard “twice a year” advice inadequate — we’ve seen hinges seize in four months on Bay-facing properties. Use a grease with corrosion inhibitors, not standard WD-40, which evaporates and leaves metal exposed. Wipe old residue first; salt attracts moisture and forms a grinding paste. If your hinges are already showing orange bloom, call us before they weld themselves solid — seized hinge replacement is cheaper than cutting and fabricating new mounting plates.
Yes — custom latch fabrication to match original profiles is one of our standard services in Burlingame. We photograph your existing hardware, measure the mounting geometry, and weld a replacement from steel or stainless stock that matches the period design. For salt-air durability, we typically recommend 304 stainless for the working components with a blackened finish to blend with original iron. Cost runs $280–$450 depending on complexity. We’ve replicated latches on Easton Addition homes where the homeowner didn’t want a modern box latch marring the gate’s lines. Call (866) 550-7854 to schedule a pattern takeoff.
Written by Isaac Bloom, Owner at Highpoint Gate Repair California, serving Burlingame and the Peninsula since 2013.